Excluding blades, sold separately.
For sizes 12″- 16″

Best Quality Tools Practical, Strong and Durable
Voltage: 380V
Speed: 2900r/min
Frequency: 50Hz
Current: 6.8 A
Weight: 50 kg

Blade exit height
300mm = 50mm blade
350mm = 80mm blade
400mm = 110mm blade

Power: 3KW. 3PHASE
Table Size: 69x49x70cm

(KNIVES NOT INCLUDED)
Link blade
https://www.tokopedia.com/ptfuturestar/mata-gerinda-kayu-14-inch-mata-gerinda-potong-kayu-350-x-3-0-x-30-0

Specifications
Power 7.5KW
Blade diameter: 400 - 700mm
Electrical 380V (3 PHASE)
Water tank size: 35 - 45L
Depth of cut: 150 - 250mm

((THIS PRODUCT INCLUDES A 400MM CONCRETE BLADE))

Why should you shop at PT. FUTURESTAR INDONESIA?
1. We are FIRST HAND IMPORTERS, so our prices are very competitive.
2. Customers can COME to our store if they want to see the product in person.
3. Serving orders in LARGE / GROWING AMOUNTS

POWER: 4KW
SPEED: 1435r/MIN
POWER: 380V

TYPE: HXG132S-4
POWER: 5.5KW
SPEED: 1440r/MIN
POWER: 380V

TYPE: HXG132S-4
POWER: 5.5KW
SPEED: 1440r/MIN
POWER: 380V

1. There must be no high-voltage lines in the pile driver operation area. The operation area should be clearly marked or fenced and unauthorized persons are not allowed to enter. The operator shall monitor the pile hammer during the piling process at a distance of 5 m from the center of the hammer.
2. The diesel piling hammer shall use fuel with the specified mixing ratio, and the fuel tank shall be filled and the drain valve shall be opened before operation.
3. Before operation, the air screw should be opened to exhaust the air in the oil circuit, and the fuel pump should be checked and tested, and the fuel injection should be observed from the cleaning hole.
4. Before operation, the upper piston should be lifted slightly above the upper cylinder by means of a landing gear, and the oil plug of the oil storage chamber should be opened and filled with lubricating oil according to regulations.
5. For the newly opened pile hammer, 0.5L lubricating oil should be poured along the upper piston one week in advance, and a certain amount of lubricating oil should be added to the lower piston with an oil gun.
6. All fastening bolts must be checked.
7. After lifting the pile hammer out of the anvil, its slide length should not exceed 200mm, if it exceeds, the buckle of the pile cover rope should be adjusted.
8. the wear gap of the guide plate should be checked, and it should be replaced if the gap exceeds 7mm.
9. should check the buffer pad, when the anvil seat and rubber pad contact surface is less than 2/3 of the original area, or under the cylinder flange and anvil seat gap is less than 7mm, should replace the rubber pad.
10. For water-cooled pile hammers, the water tank must be filled with water.
11. Before starting pile hammering, the hammer, pile cap and pile should be on the same axis, and the pile should not be moved eccentrically.
12. When starting pile hammer in soft soil layer with large pile penetration, the throttle should be closed first for cold blows, then open the throttle to start pile hammer when the penetration of each blow is less than 100mm.
13. After the piles are inserted, the verticality of the piles should be corrected in time.
14. In piling, the jump height of the upper piston must not exceed that specified in the instruction manual.
15. When the upper piston falls and the diesel hammer does not start, the upper piston may have a short bumpy period, at this time the landing gear should not fall, and should prevent it from hitting the touch block.
16. During the stacking process, there should be a person responsible for pulling the control rope on the crank arm.
17. When the upper piston is disengaged from the starting hook, the landing gear should continue to be lifted, and it is desirable to make it reach or exceed a distance of 2 m from the upper cylinder.
18. During operation, the focus should be on whether the upper piston lubricating oil leaks out of the oil hole.
19. During operation, when the impact energy of the pile hammer reaches the energy, the hammer penetration value ***10 shall not be less than 5mm.
20. The packing in the pile cap shall not be skewed and the center of the pile cap shall be hammered during operation.

Permanent Magnet Lifter is an ideal tool for lifting objects.
heavy materials such as iron plates easily, quickly and economically.
Capacity: 1000kg

Capacity: 400kg
dimensions 15.5 x 9 x 9.5 cm
Actual weight of product 11KG

Capacity: 600kg
Dimensions 21 x 10.5 x 12cm

Why should you shop at PT. FUTURESTAR INDONESIA?
1. We are FIRST HAND IMPORTERS, so our prices are very competitive.
2. Customers can COME to our store if they want to see the product in person.
3. Serving orders in LARGE / GROWING AMOUNTS

futurestar is a professional lifting magnet supplier with more than 10 years export experience. We can provide PML series heavy duty lifting magnet from rated capacity 100kg to 6000kg. Customers can choose 3 times or 3.5 times safety factor according to the actual use situation.

Specifications
Production Capacity: 5-6m3
Max Conveying Distance: Horizontal 200m, Vertical 50m
Applicable Material Ratio: cement/sand = 1: 3-5
Water Cement Ratio: <0.4
Aggregate Diameter: <20
Delivery Pipe Inner Diameter: 51
Rotor Body Diameter: 440mm
Power 5.5Kw
Weight: 700 KG

Maximum delivery distance: Flat 30M, top 20M
The largest aggregate size: 15mm
Air consumption: 10 - 15m3/min
Voltage: 380V
Production capacity: 5 - 7 m3/h
Bone particle diameter: 64mm/51mm
Pressure: 4 - 6.0 Mpa
Power: 6 - 7.5KW
Dimensions: 220 x 930 x 1180mm

Why should you shop at PT. FUTURESTAR INDONESIA?
1. We are FIRST HAND IMPORTERS, so our prices are very competitive.
2. Customers can COME to our store if they want to see the product in person.
3. Serving orders in LARGE / GROWING AMOUNTS

Pipe threading machine is a tool that functions to make threads on iron pipes.
Specifications
TYPE: Z1T-R2
Capacity: 1/2 inch - 2 inch
Thread speed: 27 rpm
Power: 750 W / 2,800 rpm
Voltage: 220V
Frequency: 50Hz

TYPE Z1/3T-R4II
Capacity: 1/2 inch - 4 inch
Thread Speed: 27 rpm
Power: 750 W / 2,800 rpm
Voltage: 380V
Frequency: 50Hz

Sleeving machine is equipped with forward and reverse device, used for processing pipe external thread electric appliance. Also known as: electric pipe cutting and strapping machine, strapping machine, pipe thread strapping machine.
The sleeving machine consists of: machine body, motor, speed reducer, pipe chuck, plate screw head, cutter seat, knife feeding device, cooling system.

Specifications:
1. diameter range of processed steel bars: 12-32mm
2. main motor power: 4kw
3. equipped with three-phase power supply: 3- 380v 50Hz
4. spindle speed: 40-62r/min
5. for maximum processing length 80mm
6. drat yield 2.5-3mm
7. weight: 500kg
*ALREADY INCLUDED 1 SET SPAREPART (rool, knife, L key, rool axle)
*WE ALSO SELL THEIR SPAREPARTS (if you want additional)

Specifications:
1. diameter range of processed steel bars: 14-40mm
2. main motor power: 7.5 kw
3. equipped with three-phase power supply: 3- 380v 50Hz
4. spindle speed: 40-62r/min
5. for maximum processing length 80mm
6. drat yield 2.5-3mm
7. weight: 500kg
*ALREADY INCLUDED 1 SET SPAREPART (rool, knife, L key, rool axle)
*WE ALSO SELL THEIR SPAREPARTS (if you want additional)

Concrete shotcrete machine is widely used in house protection works, roads, tunnels, culverts, subways, bridges, coal mines and other projects as well as spraying and repairing industrial kilns.

Concrete shotcrete machine is widely used in the protection work of houses, roads, tunnels, culverts, subways, bridges, coal mines and other projects as well as the spraying and repairing of industrial kilns.

Production: 6m3/hour
Inner Pipe Diameter: 51mm
Air Pressure: 0.4-0.6 Mpa
Dimension: 1450x900x1290mm
Max. Carrier Distance: Flat 200m / Above 20m
Aggregate Size: 20mm
Air Consumption: 7-8m3/min
Voltage: 380V
Weight: 700Kg
WORKING EFFECT
Concrete shotcrete machine is widely used in the protection work of houses, roads, tunnels, culverts, subways, bridges, coal mines and other projects as well as the spraying and repairing of industrial kilns.
WORK EFFECT
Concrete shotcrete machine is widely used in house protection works, roads, tunnels, culverts, subways, bridges, coal mines and other projects as well as spraying and repairing industrial kilns.
Why should you shop at PT. FUTURESTAR INDONESIA?
1. We are FIRST HAND IMPORTERS, so our prices are very competitive.
2. Customers can COME to our store if they want to see the product in person.
3. Serving orders in LARGE / GROWING AMOUNTS

HIGH PRESSURE AIRLESS PAINT SPRAY MACHINE

Specifications
PUTIAN Product Brand
Voltage Frequency: 220-240V/50Hz
Spray Distance: 350-400mm
Product Weight: 17.5KG
Exit Pressure: 23MPA
Pipe Pressure Strength: 60MPA
Product Model: PT-280E
Power: 1200W
Spray Width: 250MM
Nozzle Diameter: 0.15-0.22MM
Injection Flow: 2.3L/MNT

Why should you shop at PT. FUTURESTAR INDONESIA?
1. We are FIRST HAND IMPORTERS, so our prices are very competitive.
2. Customers can COME to our store if they want to see the product in person.
3. Serving orders in LARGE / GROWING AMOUNTS

WALL PLASTER SPRAY MACHINE

For consultation / fast respone service, please contact:
0813-1187-9789

Specifications
Pressure: 4Mpa
Height: 10/20m
Particle size: < 6mm
Water: Ash: Sand: 0.7-1:1: 3
Delivery flow: 3 m3/h
Volume: 90L
Weight: 375kg
Suitable air compressor: 0.3 - 0.6m3
Suitable nozzle: 32mm
Electricity: 380V
Power: 2.2kw 7.5kw

Why should you shop at PT. FUTURESTAR INDONESIA?
1. We are FIRST HAND IMPORTERS, so our prices are very competitive.
2. Customers can COME to our store if they want to see the product in person.
3. Serving orders in LARGE / GROWING AMOUNTS

Wall Plaster Spray Machine

Engine: Diesel (Diesel fuel)
Pressure: 6 Bar
Particle size: 10mm maximum
Hopper volume: 80 Liters
Include 10 meter hose

Note: The weight stated in the system is only for invoice delivery.